Bonjour,

Voil? ce que la version d?finitive doit donner :

?Wasia B7 firmware? for the Canon Digital Rebel (300D)
Released June 1, 2004
All enhancements
? Custom function menu found on the last page in the menu

? Ability to define how the SET button behaves (same menu found on the 10D - refer to the 10D manual for full
explanation of these new enhancements)

? Exposure level increments either 1/2 or 1/3-stop

? Option to enable 1/200th flash speed sync in AV mode

? Ability to change the JPG size when shooting in RAW mode

? Shutter release with or without CF card

? FEC adjustment via the JUMP button, use the dial to adjust as shown on the LCD

? ISO3200 now available, and is represented by an "H" in the LCD - same as how the 10D shows this

? Mirror lockup available via enabling the option in the custom function, works by pressing the shutter button which
flips the mirror up, then the shutter opens about 1-1.5 seconds after MLU - note that this is different than how it is
implemented on the 10D where you press once to flip the mirror and press again to open the shutter

? Immediately pressing the ERASE button after taking a photo, you can delete the photo by pressing the ERASE
button again instead of selecting Ok previously, to not delete the photo press any other key

? Left button changes the focus mode and is displayed on the LCD as follows:
o PA-0 Lens set to manual focus
o PA-1 One shot
o PA-2 AI-Servo (selectable but cannot take a photo - one workaround, hold the shutter button all the
way down then switch the lens to manual focus)
o PA-3 AI-Focus (first takes one shot then the camera may switch to AI-servo depending on what you are
focussing on)

? Right button is for changing something (believe it's metering) but this does not do anything - so ignore (values if
you're curious are PA-0, PA-1 and PA-2)
Custom Function Menu
For further explanations on these custom functions please refer to the 10D manual.
CF1 SET button func. when shooting (works)
0 Default (no function)
1 Change quality
2 Change parameters
3 Menu display
4 Image replay

CF2 Shutter release w/o CF card (works)
0 Possible without CF card
1 Not possible

CF3 Flash Sync speed in Av mode (works)
0 Auto
1 1/200sec (fixed)
CF4 Shutter button / AE lock button
0 AF/AE Lock
1 AE Lock/AF
2 AF/AF lock, no AE lock
3 AE/AF, no lock

CF5 AF-Assist Beam / Flash firing
0 Emits/Fires
1 Does not emit/Fires
2 Only ext. flash emits/Fires
3 Emits/does not fire

CF6 Exposure level increments: (works)
0 1/2-stop
1 1/3 stop

CF8 RAW+JPEG rec. (works)
0 RAW+Small Normal
1 RAW+Small Fine
2 RAW+Medium Normal
3 RAW+Medium Fine
4 RAW+Large Normal
5 RAW+Large Fine

CF9 Bracket. sequence/auto cancel
0 0,-,+/enable (300D default)
1 0,-,+/disable
2 -,0,+/enable
3 -,0,+/disable

CF10 Superimposed display
0 on
1 off

CF11 Menu button display position
0 previous(top if powered off)
1 previous
2 top

CF12 Mirror lockup (works)
0 disable (300D default)
1 enable

CF14 Auto reduction of fill flash
0 enable (300D default)
1 disable

CF15 Shutter curtain sync [NO]
0 1st curtain sync
1 2nd curtain sync

CF16 Safety shift in av or tv
0 disable
1 enable

CF17 Lens af stop button function
0 af stop
1 af start
2 ae lock while metering
3 af point: m->auto/auto-ctr.
4 one shot -> <- ai servo
5 IS start

Watchouts

? Camera may lock up if you attempt to change the language, maybe possible to change the language but
must be done on the original Canon 300D 1.1.1 firmware

? Some features may not work correctly if you are using another language - use English as a workaround

? If you upgrade and some of the things don&#39;t seem to work properly, set the settings in the Custom
Function back to the original values (see below) and install the original 1.1.1 firmware, then upgrade to
the new firmware

? Change the SET button to something other than FEC before upgrading to this version

? When the MLU is enabled and using the self timer, the timer will countdown and beep for 2 seconds then
pause another 7-10 seconds with no countdown in the LCD or beep.

? Names for modes via left/right button will be updated to something more meaningful

? MLU does not work properly when using a flash ? flash will fire when the mirror is lifted ? not when the
shutter opens

Revertng back to the original version

? Reset all the Custom Function values to the original 300D settings. Note, you cannot use the Reset
option in the menu, it does not affect these values. Below is a list of default binary values from left to right
(the bottom numbers in the CF menu):
0,0,0,0,0,1,0,11,0,0,0,0,0,0,0,0,0

? Flash back to 1.1.1.

Voil? en croisant les doigts

A plus